H850 Catalog Page
Home Page
Routing Tools Phone: 516-328-3970 www.technocnc.com  61 For Use On: Softwood: Cedar, Cottonwood, Pine and Redwood Hardwood: Ash, Beech, Birch, Cherry, Mahogany, Maple, Oak, Poplar, Teak and Walnut Designed as an economical alternative to Solid carbide for solid wood routing. For Use On: Softwood: Cedar, Cottonwood, Pine and Redwood Hardwood: Ash, Beech, Birch, Cherry, Mahogany, Maple, Oak, Poplar, Teak and Walnut Designed as an economical alternative to Solid carbide for solid wood routing. Downcut spiral design when fixturing is such that both chips and material are better off forced down. Solid Wood & Wood Composites 40-Series    Single Edge    High-Speed Steel    Upcut Spiral 40-Series    Single Edge    High-Speed Steel    Downcut Spiral 1/4 1/4 1/4 1/4 1/2 1/4 5/16 3/8 1/2 1/2 3/8 1/2 1/2 1/2 1/8 5/32 3/16 7/32 1/4 1/4 1/4 1/4 5/16 5/16 5/16 5/16 3/8 3/8 3/8 1/2 H25XOS-40-001 H25XOS-40-051 H25XOS-40-003 H25XOS-40-053 H25XOS-40-005 H25XOS-40-007 H25XOS-40-009 H25XOS-40-011* H25XOS-40-015 H25XOS-40-019 H25XOS-40-021 H25XOS-40-023 H25XOS-40-031 H25XOS-40-033 H25XOS-40-035 H25XOS-40-043 H25XOS-40-037 H25XOS-40-039 H25XOS-40-041 2-5/8 2-7/8 2-7/8 3 2-3/4 2-3/4 3-1/4 3 3 3 3-1/4 3-1/2 3 3-1/2 3-3/4 3 3-1/4 3-1/2 4-1/2 3/8 5/8 5/8 7/8 5/8 3/4 3/4 1 1 1 3/4 1 1 1 1-1/4 1 1-1/4 1-1/2 1-1/2 Catalog Number Shank Dia. Overall Length Helix Angle P19°-32° shear *These tools are designed and toleranced for air routers with guide bushings. Helix Angle P19°-32° shear *These tools are designed and toleranced for air routers with guide bushings. Cutting Edge Dia. Cutting Edge Length H25XOS-40-002 H25XOS-40-052 H25XOS-40-004 H25XOS-40-054 H25XOS-40-006 H25XOS-40-008 H25XOS-40-010 H25XOS-40-012 H25XOS-40-058 H25XOS-40-022 H25XOS-40-016 H25XOS-40-024 H25XOS-40-032* H25XOS-40-030* H25XOS-40-034 H25XOS-40-036 H25XOS-40-044 H25XOS-40-038 H25XOS-40-040 H25XOS-40-042 1/4 1/4 1/4 1/2 1/4 1/4 1/2 5/16 1/2 3/8 3/8 1/2 1/2 1/2 1/8 5/32 3/16 7/32 1/4 1/4 5/16 5/16 5/16 3/8 1/2 2-5/8 2-7/8 2-7/8 3 2-3/4 2-3/4 3-1/4 3 3-1/4 3-1/4 3 3-1/2 3 3-1/2 3-1/2 3-3/4 3 3-1/4 3-1/2 4-1/2 3/8 5/8 5/8 7/8 5/8 3/4 3/4 1 1 3/4 1 1 1 1 1 1-1/4 1 1-1/4 1-1/2 1-1/2 Catalog Number Shank Dia. Overall Length Cutting Edge Dia. Cutting Edge Length